Biocop TF Antifouling Paint
Complete Your Purchase
Biocop TF Antifouling Paint utilizes ablative, dual-biocide technology to combat hard-shell fouling and slime.
With its dual-biocide ablative formula, Biocop TF delivers multi-season protection against hard and soft marine growth. Biocop TF accomplishes this via a polymer binder system engineered to optimize the release of copper, which prevents hard-shell fouling, and zinc omadine, which prevents slime.
As an ablative paint, Biocop TF slowly wears away or “self-polishes” at a controlled rate as the boat is used. The benefit of this slow-wearing process is threefold: First, fresh biocide is constantly released for unbroken antifouling effectiveness. Second, the build-up of old, spent paint is reduced along with the need for sanding at haulout. Third, as Biocop TF wears away or “self-polishes”, drag is reduced and fuel efficiency is enhanced. Biocop is a suitable choice for use on fiberglass, wood, and steel hulls in salt-, brackish-, and freshwater environments. Do not apply to aluminum hulls. Not for sale in States where prohibited by law.
Key Features
- Copper biocide prevents hard growth
- Zinc omadine prevents slime
- Polymer binder system optimizes biocide release
- Constantly releases biocide for unbroken antifouling effectiveness
- Slow-wearing formula reduces paint build-up
- Self-polishes with Delivers multi-season antifouling protection
Physical Data
- Type: Dual-biocide ablative
- Finish: Semi-gloss
- Available Colors: Red, Blue, Dark Blue, Gray, Green
- Components: 1
- Curing Mechanism: Solvent release
- Solids by Weight: 80% +/- 2%
- Solids by Volume: 57% +/- 2%
- Coverage: 315sq.ft./gal.
- VOC: 377g/l (max.)
- Active Ingredients: 38% Cuprous Oxide; 4.14% Zinc Omadine
- Flash Point: 100°F
Application
- Application Method: Brush, roller, airless, or conventional spray
- Number of Coats Recommended: 2 heavy coats onthe entire hull; Three at the waterline and other high-wear areas
- Dry Film Thickness/coat: 3mil.
- Wet Film Thickness/coat: 5.3mil
- Applicator: Maximum 3/8” nap roller
- Application Temperature Min./Max. Range: 50°F.-90°F.
- Thinner: Seahawk 2033, 2035
Drying Times*
| Drying | @73°F | @95°F |
|---|---|---|
| To touch | 2 hrs. | 1 hr. |
| To recoat (min.) | 1 hr. | 1 hr. |
| To recoat (max.) | no max. | no max. |
| To launch | 12 hr. | 12 hr. |
The above dry times are minimums. May be recoated after the minimum time shown. There is no maximum dry time before launching.
Get the right amount of paint:
Note: The following recommendations are for two coats of paint. All values are approximate.
| Boat Type | Bottom Paint |
|---|---|
| 10' Dinghy | 1 qt. |
| 14' Outboard | 1-2 qt. |
| 18' Runabout | 2 qt. |
| 20' Sailboat | 3 qt. |
| 24' Runabout | 3-4 qt. |
| 30' Sailboat | 1.5 gal. |
| 32' Cruiser | 1.5-2 gal. |
| 36' Auxiliary | 2 gal. |
| 40' Cruiser | 2.5 gal. |
| 45' Sailboat | 3-3.5 gal |
| 50' Sportfisher | 4+ gal. |
Another way to determine bottom paint quantity is to estimate the approximate surface area of the hull below the waterline, using the following formula:
Length x Beam x .75 = Approximate underwater surface area in square feet.
Each paint has a “theoretical coverage” area, but most paints require at least two coats, so you can expect actual coverage to be no greater than half of the theoretical value.
More information
For detailed application instructions, see the Biocop TF Data Sheet. NOTE: Manufacturer data sheets are subject to revision. Linked data sheets are believed to be accurate at the time of publication.
You May Also Like
